Skip to main content

MATEKSYS F722-SE

Full details on the MATEKSYS F722-SE can be found on the Matek Website: mateksys.com/?portfolio=f722-se. AlphaFly Target: MATEKF722SE

Аппаратное обеспечение Specs​

  • Mass: ~10g
  • PCB Size: 36x46mm
    • 30x30mm Hole pattern (M4 size, M3 size with rubber isolators)

FC Specs​

  • Processors and Sensors
    • MCU: STM32F722RET6
    • IMU: MPU6000(Gyro1) & ICM20602(Gyro2) connected via SPI1
    • Baro: BMP280 (connected via I2C1)
    • OSD: AlphaFly OSD (AT7456E connected via SPI2)
  • Blackbox: MicroSD card slot (connected via SPI3)
  • 5 UARTs (1,2,3,4,6)
  • 8 DShot outputs
  • 2 PINIO (VTX power switcher/user1 and 2 camera switcher/user2)

Integrated PDB Specs​

  • Input: 6-36v (3-8S LiPo)
  • ESC Pads: Rated 4x35A per ESC pad set (4x46A burst)
  • Voltage Regulators:
    • 5v BEC: 2A continuous load (3A burst)
    • 3.3v LDO: max load: 200mA
  • Power Sense:
    • Current Sensor: Rated for 184A (Suggested scale value 179 )
    • Voltage Sensor: 1:10 signal output ratio (Suggested scale value 110 )

Status LEDs​

LEDColorColor Codes
LED0BlueFC Status
LED1GreenFC Status
LED3.3Red3v3 Status

Pinout​

Pads are organised into two large banks of pads on left and right sides of board with a couple sets of pads on the underside of the board and ESC related connections near the board corners.






          __________








         /  U    U  \








/-----------------------------\








|oE                         Eo|








|SC                         SC|








|                             |








| P                        P  |








| A                        A  |








| D                        D  |








| S                        S  |








|                             |








|ES                         ES|








|oC                         Co|








\------------[USB]------------/
Pad Silkscreen LabelFunctionNotes
+ / - Battery In6-36vDC LiPo Power input (Battery +/- and 4-in-1 ESC +/- pads)
S1-S8 ESC Out(1-4 near ESC power connections, 5-8 on right side) Поддержкаs PWM, Oneshot, Multishot, DSHOT
GND, S1-S4 ESC Out(Rear of board) 4-in-1 ESC Out
VBat GND VBAT OutVBAT power pad (marked for VTX), power ON/OFF can be switched via PINIO1(PC8)
CURR Current SenseCurrent Sensor I/O pin (output from onboard sensor or input from external sensor)
5V Out from internal 5v BEC (rated 2A continuous, 3A burst)
3V3 Out from 3v3 regulator (rated 200mA)
4V5 Out from 4v4~4v8, 0.5A (power is also supplied when connected via USB)
G GND
LED WS2812 Signal
Bz-, 5V Buzzer
CL, DA I2C1I2C connection marked for a magnetometer but could be used for whatever
VTX VTXVTX: Video out
C1/C2 CameraC1: camera-1 IN, C1: camera-2 IN, 2 camera video can be switched via PINIO2(PC9)
RX1, TX1 UART1
TX2 UART2-TX
RX2 UART2-RXRX connection for Spektrum DSMX or DSM2, FlySky iBUS, or PPM (Disable UART2 for PPM)
RX3, TX3 UART3TX3 can be used for VTX control
RX4, TX4 UART4RX4 pin PA1 can be remapped for camera control(PWM)
TX6 UART6-TX
RX6 UART6-RX(One per board corner) Duplicates of RX6 pad for ESC Telemetry
Rssi RSSIFrSky RSSI input from RX (Rear of board)
PA4 ADC/DACEXTERNAL1ADC_PIN (_Rear of board)
D+, D-. VBus USB pins(Rear of board)